2026-11-03

A 7-Step Checklist for Buying Adhesives for Facility Repairs (Tiling, Epoxy, and Everything Else)

A practical purchasing checklist for facilities and maintenance adhesives — covering tiling adhesives, fast-curing epoxy, substrate checks, TDS review, and the three ordering mistakes that cost me money.

Who this checklist is for

I'm the office administrator for a 320-person company. I manage all facilities ordering — HVAC contracts, janitorial, electrical, and the grab-bag stuff nobody else wants. Roughly $140,000 annually across nine vendors. I report to both operations and finance.

I'm not a chemist. I'm the person who ends up placing the order when someone asks "can we fix this tiled floor by tomorrow?"

This checklist is for tiling adhesives, fast-curing epoxy, structural adhesives — basically any time someone forwards you a product link and says "just buy this." There are seven steps, and the whole thing takes about 15 minutes. I've been running it for two years. It has saved me one return, one scrapped pallet, and at least one blown crew schedule.

Step 1: Lock the substrate and conditions before you ask for a price

The mistake I see most often (and made myself, twice) is asking for pricing first and "will this stick?" second. Flip that.

Before you request a single quote, get a written answer to six things:

  • What's being bonded to what — tile to concrete, tile to plywood, metal bracket to masonry, etc.
  • Indoor or outdoor, and whether there's standing water or freeze-thaw cycling
  • Service temperature range — a warehouse floor near a loading dock isn't the same as a breakroom backsplash
  • Movement — is this a rigid panel or something that flexes?
  • Time window — how long before foot traffic or load?
  • Coverage area, not "units." Ask for square meters or linear measurement

Checkpoint: you should be able to state the bond in one sentence. "25×25 porcelain over cured concrete slab, interior, wet area, needs foot traffic in 8 hours." If you can't write that sentence, don't order yet.

Step 2: Separate one-off repairs from regular replenishment

These are completely different purchases and should follow different rules.

One-off repair: you need the right product in the smallest quantity available. Don't let anyone upsell you into a 20kg bucket for a 3-square-meter patch. That bucket will sit in the maintenance closet until it expires, and it will expire.

Regular replenishment: now volume, shelf life, and batch consistency matter. That's when it's worth setting up a standing order or a distributor agreement instead of buying cartridges one at a time.

Checkpoint: if the job is under one full container of the smallest package size, buy the smallest package. Full stop.

Step 3: Narrow the adhesive type with two questions

Quick answer to "what are the different types of adhesives" — for facilities work, you're usually dealing with six families:

  • Cementitious tile adhesive (thin-set) — the default for floor and wall tile, especially wet areas. Rated under ANSI A118.4 for modified thin-set; ANSI A118.10 covers waterproof membranes. Cheap, forgiving, and the standard for a reason.
  • Epoxy adhesives — two-part, high strength, bonds metal, stone, concrete, cured tile. Also the go-to for fast-curing epoxy repairs where you need load-bearing strength in hours, not days.
  • Polyurethane adhesives — flexible, good for dissimilar materials and anything that moves slightly. Common in exterior and heavy-duty settings.
  • Cyanoacrylate — instant grab, tiny areas, non-structural. Fine for a chipped trim piece, useless for a floor.
  • Silane-modified polymer (MS polymer) — elastic, low-odor, tolerant of damp surfaces. Good for repairs in occupied spaces.
  • Silicone sealant — joints and perimeters. Not a structural bond. If someone specifies silicone for a load-bearing tile repair, push back.

The two questions that narrow it fastest: (1) does the joint need to stay rigid or flex? and (2) does the surface stay wet? Rigid + dry = cementitious or epoxy. Flex + wet = polyurethane or MS polymer. That single fork eliminates about 80% of the catalog.

Checkpoint: you have a family, not a SKU. Don't pick a brand yet.

Step 4: Download and read page one of the TDS before you order

This is the step most people skip, and it's the one that actually protects you. The technical data sheet — not the marketing page — carries the numbers: open time, working temperature, coverage per unit, tensile strength, cure schedule.

For anything epoxy-based, I pull the TDS from the manufacturer's own material download area. Huntsman's site has one of the more usable versions of this (their huntsman download section bundles TDS and SDS together without a registration wall), and I've used it as a cross-reference even when we ended up buying another brand — because the test methods are stated the same way across suppliers.

What I actually look at on page one:

  • Mix ratio, if it's two-part (grabbing the wrong ratio is the single most common failure)
  • Coverage per kilogram or per cartridge, with the trowel size stated
  • Substrate preparation requirements — some products demand a primer and won't tell you on the box
  • The test standard cited (ASTM C627 for tile systems, ISO 4587 for lap shear strength)

Checkpoint: you can name the test standard on the product. If the datasheet doesn't cite one, that's a signal.

Step 5: Break "fast-curing" into four separate numbers

"Fast-curing" on a label means almost nothing. There are four different clock values, and confusing them is how schedules slip:

  1. Pot life — how long you have to work with the mixed product
  2. Initial set — when it stops moving, not when it's strong
  3. Full cure — when it reaches rated strength
  4. Traffic / load time — when it's safe to walk on or load

They can be wildly different. A fast-curing epoxy might set in 15 minutes, reach full rated strength in 7 days, and allow foot traffic in 4 hours. If the crew is planning around "fast," they're planning around the wrong number.

Temperature swings all four. A product rated for 24-hour cure at 23°C might need 72 hours at 12°C — which, in an unheated loading dock in February, is the whole job.

Checkpoint: you've confirmed the number that matches the actual constraint (when does the crew leave, when does the area reopen). Not the number on the headline.

Step 6: Compare cost per square meter, not cost per tube

Cartridge pricing is a trap. Two products at $18 and $26 per unit can flip order completely once coverage and trowel size are factored in — a cheaper cartridge that covers 4 m² loses to a pricier one covering 9 m².

Rough math I run every time: unit price ÷ stated coverage, then add primer, mixing nozzles, and disposal. Mixing nozzles are stupidly expensive in volume (often $1.50–$4 each), and one two-part cartridge can eat three of them. That line item has killed more "cheaper" options than anything else.

Also check minimum order quantity and shelf life together. A great per-kilo price on a 20kg pail you'll use 3kg of is not a great price.

Step 7: Confirm invoices, packaging, and returns before you commit

This is where being the admin person is an actual advantage, because finance will ask me about it later.

  • Invoice format — can they issue a proper PO-matched invoice, or is it a handwritten delivery slip? I learned that one the expensive way.
  • Packaging — how is the product arriving? A pallet of 20kg pails with no liftgate service means someone's unloading it by hand.
  • Return policy on opened units — most chemical suppliers won't take back opened containers. Confirm before, not after.
  • Batch/lot number on delivery — matters if you're using the product in a regulated or inspected space.

Notes and the three most common mistakes

The "a glue is a glue" myth. That thinking comes from an era when the shelf held one solvent-based contact cement and one generic epoxy. The catalog hasn't looked like that in over a decade. There are now single products specified for one substrate pairing only.

The rushed buy. Two summers ago I had about 90 minutes to pick between two epoxies before the crew's access window closed. Normally I'd pull the TDS and compare cure schedules — there was no time, so I went with the one whose rep had answered the phone. It worked out. If it hadn't, I would have been the one explaining to the VP why the floor wasn't walkable Monday morning. In hindsight I should have pushed the schedule a day.

The three errors that actually cost money:

  1. Buying by unit price and ignoring coverage and consumables
  2. Ignoring shelf life on a job that'll be done in stages — the leftover pail hardens before stage four
  3. Letting the product cure schedule get decided by the crew's calendar instead of the other way around

None of these get caught by a cheaper quote. They get caught by fifteen minutes at the desk before you click order. Five minutes of verification beats five days of rework — I've got the receipts on that one.

Document-aware reading

When a Mosaic article discusses performance, readers should check whether the value is tied to a named test method and whether the statement applies to a resin grade, an application, or a finished article. Safety references should be checked against SDS Section 2. Sustainability references should identify the boundary, reporting period, and verification status before being reused in customer documents.

Next steps

For grade-specific support, contact Mosaic with the application, destination market, annual volume estimate, and required SDS, TDS, or CoA revision. The technical team can then route the inquiry without broad assumptions.

Previous: The 8-Step Checklist I Use Before Every Coating & Adhesive Order (After $3,800 in Wasted Material) Next: The 'Organic' Trap in Starch Sourcing: Why the Cheapest Quote Isn't Always the Best